Manufacturers of Cove-Flex™ Flexible and Rigid Polyurethane Mouldings

Thousands of profiles available

Custom moulding

Contract and private label moulding

Products

Cove-Flex™ Flexible and Rigid Polyurethane Mouldings, Cove-Flex™
Flexible products shipped within 5 days
Choose from thousands of profiles, Custom, Private Label or Contract moulding
Manufactured in Canada

Private Label & Custom Mouldings

Call us at 877-882-2718 so we can provide mouldings to your exact specifications.

Measuring

Mesuring1

Installation

Cove-Flex™ Step-by-Step Installation Tips

  1. Lay out the material and let it acclimatize to room temperature and relax in its original shape. Cove-Flex™ Mouldings handle best between 18°C and 22°C (65°F & 72°F). Do not soak the mouldings in hot water.
  2. For INSIDE CURVES, measure the length required and add 1/8 inch. Dry fit the moulding, shimming and trimming as necessary to get the perfect fit.
  3. For OUTSIDE CURVES, measure the length required and add 1/8 inch, but do not trim the moulding for extra material.
  4. Clamp, tape or wedge the material in place. Start in the MIDDLE of the piece and work evenly on either side to the ends so the material is not stretched and flat spots in the curve are eliminated.
  5. Compare the thickness of the Cove-Flex™ product to the thickness of the matching wood product where the two will meet. It may be necessary to shim or plane off either product to align material perfectly.
  6. Pre-drilling all nail and or screw holes is recommended for best application. Alternatively, an 18 gauge pneumatic PIN NAILER may be used to fasten the moulding in place. It is recommended that all nails or screws are placed no closer than 3/8 inch from the edge or end of the moulding.
  7. ALWAYS use a strong construction adhesive (PL PREMIUM preferred) and confirm the surface you are applying material to is flat and smooth.
  8. NEVER use staple guns.
  9. NEVER overstress the material.
  10. Fill and lightly sand the material as for wood, taking care not to damage any surface or wood grain pattern.
  11. Clean material before painting or staining using a non-corrosive cleaner.
  12. The surfaces may be coated using acrylic or oil based paint and stain. NOTE: ALKYD based paints and stains are NOT RECOMMENDED. Traditional stains will not work as they need a porous surface to soak into, as such use any gel or solid stain to achieve your desired effect.
  13. Some mouldings may be special ordered with a darker tint. For unpainted surfaces avoid prolonged exposure to direct sunlight unless a UV inhibitor has been applied.

Warranty

  • Cove Moulding Group warrants its products against defects in materials and workmanship for a period of five years from the date of purchase.
  • The purchaser and installer must have inspected each and every part prior to installation.
  • Any defects that could have been discovered by appropriate pre-installation inspection are not covered after installation has occurred.
  • This Limited Warranty only covers materials that have been handled and installed utilizing recognized standards within the industry as they would apply and including, but not limiting, any additional instructions contained within this publication.
  • Cove Moulding Group maintains the right have any parts covered by warranty inspected while determining in its own discretion whether or not the parts are defective.
  • Cove Moulding Group will repair or replace parts determined by them as defective if returned freight prepaid to Cove Moulding Group at their manufacturing facility in Surrey, British Columbia.
  • Alternative arrangement may be made at the discretion of Cove Moulding Group.
  • Cove Moulding Group will not be liable for incidental or consequential damages such as, but not limited to, labour, finishing, parts damaged by freight carriers, freight charges, installation, lost profits, lost sales or the like. It is the purchasers' responsibility to ensure that products conform to local building codes.

Send us a message.

And we will get right back to you.